How To Grow Grape Vines At Home

By | November 6, 2016

Growing Grapes

We have plenty of wild concord grapes on our property. However, the insurance company doesn’t approve of our harvesting methods so it’s probably best to plant some cultivated grapes. When I cleared the land for the greenhouse, it left plenty of area to plant various fruit producing plants which don’t need the greenhouse to thrive. Plus why waste the space just growing grass? Taking a look at my 3rd grade drawing skills, I’m going to set three 4x4x10′ treated posts 34 feet into the ground and space them 24′ apart. This will allow for 8 plants in the space. Then I’ll string 12 gauge galvanized wire starting with the first wire 4246quot; from.

The ground, then space the other two 12quot; apart. The plants can be spaced 6′ apart and over time the vines can be trained along the 3 wires. I had planned to set the posts first in the event that I hit any large rocks while digging, however I blew a seal on the backhoe and had to find some parts for it. So I took my chances and put the plants in first. The row should go in a straight line and a 100′ tape measure works well for marking out the locations of each post and plant. Jamming a piece of survey’s tape at each mark does the trick. We’re going oldschool and using a pickaxe and shovel and digging a hole about 1 foot deep. Luckily there weren’t any large rocks in the way just.

A few roots and small stones that the pickaxe was able to pluck out. Later, looking at the post holes, you’ll see why I didn’t dig them by hand. Planting the vines is fairly easy. I got these seedless concord grapes from Gurney’s for half price. I just remove the fiber that’s used for keeping the roots damp, spread out the roots a bit, and set it in the hole so that all the roots that emerge from the vine will be just below the finished level of the soil. All the dirt that came out of the hole was hardpan so I filled it with nice organic soil, then compacted it down, and gave it a really good watering. It also important to cover the area with mulch to help maintain.

The moisture in the soil until the roots can get established. These will get watered every day for a couple of weeks. The actual work of planting the vines is quick. It’s the preparation of digging out the rocks that takes all the time. A 30 cent Oring and a day to dismantle and reassemble the valve assembly and the backhoe is running again. I can now install the posts for the wire arbor. It may not be the fastest backhoe, but it beats digging through the rock with a pick and shovel. The holes are dug to about 4 feet which will provide a deep enough anchor to prevent the posts from leaning.

From the future weight of the vines. Some of the rocks that I pulled out where bigger than the hole. If I had to dig these by hand, I probably would have only dug down a couple of feet, and then would have to anchor the posts with concrete and guywires. It seems like a really big hole for a post, but without an auger with rock drilling bit, it’s probably the easiest way to set a post. A little cleanup at the bottom of the hole and it’s ready. I’m using 4×4 treated lumber rated for direct burial. I’m not a fan of using treated lumber, but in order for it to last a long time, it’s a necessary evil. I like to add two temporary cleats to the post to help support it while I’m set it plumb.

And backfill the hole. I also like to drop a few rocks around the base to hold it in place when I start to fill it in. I’ll fill the hole several inches at a time and compact it between each layer, then clean up the area with some more woodchip mulch. The first wire starts roughly 4246 inches from the ground and the second and 3 wires are spaced 12 inches apart. It will be the perfect snacking height for the deer. At each marking I’ll drill a 38quot; hole through the post and then put in a 516quot; eyebolt. The back side has a large fender washer and nut. Having a large washer will help to keep the nut from pulling into the post under the weight of the vines. It’s fairly important to make.

Sure the eye bolt is an inch or more too long so you can tighten the nut if there’s a little slack in the wire. I’m using 12 gauge galvanized wire and I like to roll it out first and cut it to its rough length. Then I insert it through the bolt and bend it back on to itself, anchoring it with a wire clamp. The wire is stiff enough where you probably could just twist it over itself, but I just prefer the wire clamp. I drilled holes through the center post, but most people usually just staple the wire to the side of the post. I’m a bit obsessive compulsive and can’t handle having a bunch.

How to Prune Grapes Summer

Hi, I’m Tricia, a California organic gardener and today we’re going to talk about summer maintenance for your table grapes we’ve had an extremely wet season this year and my table grapes have gone bonkers I’m growing four different types of table grapes here and there’s a lot of vegetative growth making for a very dense canopy over the grape vines earlier in the spring, the shoots were thinned when they were about six to twelve inches long you should have about six to eight shoots per foot of canopy at the same time as thinning the shoots, I also cut the suckers off at the trunk.

And i’m going to continue to trim these suckers throughout the season, as necessary you see there’s not enough sunlight getting into this little fruit clusters the sunlight is what helps improve the flavor and the quality of the fruit by having so much foliage around the cluster, I’m also at risk for disease the first step is to take these long shoots and tuck them into the trellising and keep them out of the fruiting zone that helped a lot but you can see there’s still a lot of hanging vines I’m going to trim back this shoot that has no clusters on it.

If you’re going to trim back a shoot that has clusters, be sure and leave about 1517 fullsized leaves before you make your cut cut as little as possible and try to cut at the point where the leaves are half the size of the mature leaves these smaller leaves haven’t started producing food yet so the vine won’t miss them as much as it would miss these larger food producing leaves the grape vines are looking a lot better the cutting is going to stimulate the growth so you don’t want to do this too late in the season if the fruit is just beginning to ripen, it’s too late to cut.

Now that I’ve tamed the vines, it’s time to thin the fruit cluster thin when the fruit has just set and before it gets too big for goodsized table grapes leave one cluster per shoot in order to improve the size of the grapes, snip off the very bottom of the cluster I’m happy to have completed my summer maintenence on my table grape vines now I look forward to grape jam, grape jelly, grape juice, and those frozen grape treats so enjoy your grape vines and Grow Organic for Life!.

Leave a Reply