Building A Grape Vine Fence

By | December 24, 2016

How to Fix a Trellis on a Stone or Brick Wall

Hi I’m Craig Phillips and welcome to my trade tips. Today I’m out in the garden, and I’m going to show you how you can fix trellis to a stone wall. The first stage is to find the location in your garden that is suitable for your plants. Offer it up against the wall and just put one mark on the brick when you are happy with the height. Using a 4mm wood drill piece I am going to drill a clearance hole through all four corners. This will allow the screw that I’m using to sail through. Now all four clearance holes are drilled in the trellis, I have chaged the setting on the drill to a ‘hammer action’ setting and I have used a masonry drillbit in here. So I am going to drill through the clearance hole and mark up for a pilot hole in the stonework.

Remeber when drilling any type of stonwork allways use your safety goggles. Once I have made my first mark into the stonework I can drill all the way. With this really tough stonework Ihave started off using a smaller masonry drillbit, just 6mm, that will act as a pilot drill and then I will put a larger one in there to make the right size hole for the irght size plug. Now the 8mm hole is drilled into the blockwork, I can apply a 8mm rall plug, I can push my screw through the clearance hole of the trellis. lift it into position. At first tighten it by hand, once it starts to bite. Take your drill and drive it in. Once you have got the one screw in it it will start to take the weight. As you can see the trellis will move at this point.

So it is ideal for getting your spirit level on, let the first screw take the weight, Get it perfectly level and mark it up with your pencil Around all four corners. Once you have got it perfectly level, then change the drill setting back to the hammer action, put a masonry drillbit in and drill through through your last three clearance holes. Then you can simply slide it away, put your plugs in and screw it firmly into position. So now the one screw is taking the weight of the trellis and holding it into position. I am now going to drill pilot holes through the other three clearance holes.

Mark the wall first Then I can simply slide the trellis to one side which will allow me then to drill the brick work. drilling Once you have got all four screws firmly screwed in to the corners, your trellis is now complete. All you have to do is decide what plants you want to grow on it. If you are planning any DIY tasks in the near future, you may need a little bit of advice on tools or some top DIY tips. Well visit silverlinetools .

Basics of a Grapevine Trellis

I’m Lee Tyre with the Northampton County Cooperative Extension Service, and we’re going to talk about constructing grape vine trellises. A grape trellis is a structure that holds the vines off the ground, allowing sunlight in evenly, and making management and harvesting of the grapes easier. There are several different types of trellises. What we’ve constructed here today is a very simple one, what’s called a “high cordon grape trellisâ€�. The grapes we are training to the trellis today are an American type, and they prefer to grow downward. So.

What we’ve done, is we are going to train the cordons, the heavy limbs of the grape vine, along the top wire here, and as they grow, they’ll send laterals downward. And we’ll probably come in later and add a second wire, here below it. As you can see here, older, mature vines can become quite large, putting a good deal of strain on the trellis. Since we want these structures to last for a long time construction materials is an important consideration. You want to make sure you use materials that are resistant to decay, and can support the weight of mature vines.

Once you have selected your materials, it’s time to begin construction. When setting your end posts, make sure they are anchored well. With a short trellis, this could be a 4â€� by 4â€� post sunk 2 to 3 foot into a clay soil. With longer runs, or looser soils, setting the posts in concrete or additional bracing may be required. With a long enough run, even very large posts like this one require extra bracing to help support the load. Of course, the last main part of a trellis is the wire. Again, you want to select a heavy enough wire to support your vine for years.

To come. In addition to the wire, think about adding a device to allow you to adjust the tension on the wire easily. Wires will sag with time, and something like a fence line tensioner, a turnbuckle, or other devices, will allow you to quickly, and easily adjust the tension on your vine.

Leave a Reply